LOADRDI: Loading data loading down-data ../dn/wh_dn000.000 read 2358 ensemble and 20 bins using RDI bottom track removed 30685 values because of low percent good found 3 bad bottom error velocities and discarded them removed 0 values because of high error velocity removed 0 bottom values because of high error velocity extracting 1687 ensembles as profile removed 0 profiles due to larger tilt than 22 removed 0 profiles due to larger tilt difference than 4 multiply weight of bin 1 by 0.5 Outlier discarded 933 bins down looking ==> load data took 12 seconds GETDEPTH: Integrating depth from vertical velocity starting run 1 to find bottom depth make soundspeed based on pressure and ADCP temp last depth from int W is :4.7212 should be :2 maximum depth from int W is :1385.8257 should be :1355.7 bottom found at 1361 +/- 0 m starting run 2 to find bottom depth last depth from int W is :4.7212 should be :2 maximum depth from int W is :1355.7435 should be :1355.7 bottom found at 1360 +/- 0 m removing 583 values below recognized bottom make soundspeed based on pressure and ADCP temp correct velocities for sound speed remove data at begining and end of cast ==> get depth took 3 seconds PREPINV: prepare data for inversion, form Super-Ensembles average profiles over (p.avdz) 20 meter discarded 1155 bottom tracks velocities because of dist > 300 will not correct for sound speed twice remove reference velocity and average ensembles Outlier discarded 102 bins down looking reduced ensemble size is 126 GETINV: compute best velocity profile vertical resolution (ps.dz) is 20 [m] smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile found 2 ill constrained elements bottom inversion weight for bottom track is (ps.botfac) 1 add barotropic constrain ready for inversion length of d : 1462 (CTD vel) length of A1:126 (ocean vel) length of A2:67 Cholesky transform give low weight to 1% of data scan#:1 ==> prep inversion took 8 seconds GETINV: compute best velocity profile vertical resolution (ps.dz) is 20 [m] smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile found 2 ill constrained elements bottom inversion weight for bottom track is (ps.botfac) 1 add barotropic constrain ready for inversion length of d : 1450 (CTD vel) length of A1:126 (ocean vel) length of A2:67 Moore-Penrose inverse solve only down trace smooth Ocean velocity profile found 1 ill constrained elements smooth CTD velocity profile found 1 ill constrained elements Cholesky transform solve only up trace smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile Cholesky transform ==> inversion took 1 seconds GETSHEAR2: average shear profile over (ps.dz) 20 [m] maximum std (stdf) 2 of data minimum weight 0.6 of data increased error because of shear - inverse difference save results ??? Reference to non-existent field 'up'. Error in ==> e:\matlab\wh\m\savearch.m On line 89 ==> da.LADCP_up_hard_type=['']; Error in ==> e:\matlab\wh\m\laproc.m On line 126 ==> da=savearch(dr,d,p,ps,f); Error in ==> e:\cbl\ladcp\cb11\pro\cb11.m On line 94 ==> laproc cb11 Warning: File not found or permission denied. > In C:\MATLAB6p1\toolbox\matlab\general\@char\delete.m at line 35 In e:\matlab\wh\m\laproc.m at line 15 In e:\cbl\ladcp\cb11\pro\cb11.m at line 94 LOADRDI: Loading data loading down-data ../dn/wh_dn000.000 read 2358 ensemble and 20 bins using RDI bottom track removed 30685 values because of low percent good found 3 bad bottom error velocities and discarded them removed 0 values because of high error velocity removed 0 bottom values because of high error velocity extracting 1687 ensembles as profile removed 0 profiles due to larger tilt than 22 removed 0 profiles due to larger tilt difference than 4 multiply weight of bin 1 by 0.5 Outlier discarded 933 bins down looking ==> load data took 13 seconds GETDEPTH: Integrating depth from vertical velocity starting run 1 to find bottom depth make soundspeed based on pressure and ADCP temp last depth from int W is :4.7212 should be :2 maximum depth from int W is :1385.8257 should be :1355.7 bottom found at 1361 +/- 0 m starting run 2 to find bottom depth last depth from int W is :4.7212 should be :2 maximum depth from int W is :1355.7435 should be :1355.7 bottom found at 1360 +/- 0 m removing 583 values below recognized bottom make soundspeed based on pressure and ADCP temp correct velocities for sound speed remove data at begining and end of cast ==> get depth took 3 seconds PREPINV: prepare data for inversion, form Super-Ensembles average profiles over (p.avdz) 20 meter discarded 1155 bottom tracks velocities because of dist > 300 will not correct for sound speed twice remove reference velocity and average ensembles Outlier discarded 102 bins down looking reduced ensemble size is 126 GETINV: compute best velocity profile vertical resolution (ps.dz) is 20 [m] smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile found 2 ill constrained elements bottom inversion weight for bottom track is (ps.botfac) 1 add barotropic constrain ready for inversion length of d : 1462 (CTD vel) length of A1:126 (ocean vel) length of A2:67 Cholesky transform give low weight to 1% of data scan#:1 ==> prep inversion took 6 seconds GETINV: compute best velocity profile vertical resolution (ps.dz) is 20 [m] smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile found 2 ill constrained elements bottom inversion weight for bottom track is (ps.botfac) 1 add barotropic constrain ready for inversion length of d : 1450 (CTD vel) length of A1:126 (ocean vel) length of A2:67 Moore-Penrose inverse solve only down trace smooth Ocean velocity profile found 1 ill constrained elements smooth CTD velocity profile found 1 ill constrained elements Cholesky transform solve only up trace smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile Cholesky transform ==> inversion took 1 seconds GETSHEAR2: average shear profile over (ps.dz) 20 [m] maximum std (stdf) 2 of data minimum weight 0.6 of data increased error because of shear - inverse difference save results ??? Reference to non-existent field 'up'. Error in ==> e:\matlab\wh\m\savearch.m On line 89 ==> da.LADCP_up_hard_type=['']; Error in ==> e:\matlab\wh\m\laproc.m On line 126 ==> da=savearch(dr,d,p,ps,f); Error in ==> e:\cbl\ladcp\cb11\pro\cb11.m On line 94 ==> laproc cb11 Warning: File not found or permission denied. > In C:\MATLAB6p1\toolbox\matlab\general\@char\delete.m at line 35 In e:\matlab\wh\m\laproc.m at line 15 In e:\cbl\ladcp\cb11\pro\cb11.m at line 94 LOADRDI: Loading data loading down-data ../dn/wh_dn000.000 read 2358 ensemble and 20 bins using RDI bottom track removed 30685 values because of low percent good found 3 bad bottom error velocities and discarded them removed 0 values because of high error velocity removed 0 bottom values because of high error velocity extracting 1687 ensembles as profile removed 0 profiles due to larger tilt than 22 removed 0 profiles due to larger tilt difference than 4 multiply weight of bin 1 by 0.5 Outlier discarded 933 bins down looking ==> load data took 13 seconds GETDEPTH: Integrating depth from vertical velocity starting run 1 to find bottom depth make soundspeed based on pressure and ADCP temp last depth from int W is :4.7212 should be :2 maximum depth from int W is :1385.8257 should be :1355.7 bottom found at 1361 +/- 0 m starting run 2 to find bottom depth last depth from int W is :4.7212 should be :2 maximum depth from int W is :1355.7435 should be :1355.7 bottom found at 1360 +/- 0 m removing 583 values below recognized bottom make soundspeed based on pressure and ADCP temp correct velocities for sound speed remove data at begining and end of cast ==> get depth took 3 seconds PREPINV: prepare data for inversion, form Super-Ensembles average profiles over (p.avdz) 20 meter discarded 1155 bottom tracks velocities because of dist > 300 will not correct for sound speed twice remove reference velocity and average ensembles Outlier discarded 102 bins down looking reduced ensemble size is 126 GETINV: compute best velocity profile vertical resolution (ps.dz) is 20 [m] smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile found 2 ill constrained elements bottom inversion weight for bottom track is (ps.botfac) 1 add barotropic constrain ready for inversion length of d : 1462 (CTD vel) length of A1:126 (ocean vel) length of A2:67 Cholesky transform give low weight to 1% of data scan#:1 ==> prep inversion took 6 seconds GETINV: compute best velocity profile vertical resolution (ps.dz) is 20 [m] smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile found 2 ill constrained elements bottom inversion weight for bottom track is (ps.botfac) 1 add barotropic constrain ready for inversion length of d : 1449 (CTD vel) length of A1:125 (ocean vel) length of A2:67 Moore-Penrose inverse solve only down trace smooth Ocean velocity profile found 1 ill constrained elements smooth CTD velocity profile found 1 ill constrained elements Cholesky transform solve only up trace smooth Ocean velocity profile found 2 ill constrained elements smooth CTD velocity profile Cholesky transform ==> inversion took 1 seconds GETSHEAR2: average shear profile over (ps.dz) 20 [m] maximum std (stdf) 2 of data minimum weight 0.6 of data save results ??? Reference to non-existent field 'up'. Error in ==> e:\matlab\wh\m\savearch.m On line 89 ==> da.LADCP_up_hard_type=['']; Error in ==> e:\matlab\wh\m\laproc.m On line 126 ==> da=savearch(dr,d,p,ps,f); Error in ==> e:\cbl\ladcp\cb11\pro\cb11.m On line 94 ==> laproc cd e:\cbl\ladcp\cb12\pro cb12